Treehouse 2012
Treehouse 2012
First my wolf
Re: Treehouse 2012
Then my Webelos
Re: Treehouse 2012
And lastly my daughter who doesn't race but insists on building her own car
Re: Treehouse 2012
While I'm at it, the cars from 2011. A reindeer, penguin and a chinchilla.
- whodathunkit
- Pine Head Legend
- Posts: 2477
- Joined: Sat Apr 25, 2009 5:56 pm
- Location: Forgan, OK
Re: Treehouse 2012
(Where is oddzilla?) Would you look at that Penguin car!mebetree wrote:While I'm at it, the cars from 2011. A reindeer, penguin and a chinchilla.
Wow mebetree, nice job on these cars & the stands.
What type of automobile can be spelled the same forwards & backwards?
Re: Treehouse 2012
Those are sweet! Awesome job on those!
I showed my son, who is a penguin fanatic and he loved it. HE said he wants to do one like that for next years derby.
I showed my son, who is a penguin fanatic and he loved it. HE said he wants to do one like that for next years derby.
- whodathunkit
- Pine Head Legend
- Posts: 2477
- Joined: Sat Apr 25, 2009 5:56 pm
- Location: Forgan, OK
Re: Treehouse 2012
SUN GLASSES
Whodathunkit.
Good luck to you guys!Oddzilla wrote:Those are sweet! Awesome job on those!
I showed my son, who is a penguin fanatic and he loved it. HE said he wants to do one like that for next years derby.
Whodathunkit.
What type of automobile can be spelled the same forwards & backwards?
Re: Treehouse 2012
All very creative! I see your kids think like mine do! I am impressed with all the little cut outs for the dinosaur skeletons. Did you have any special tips for that, or just drill and disengage and engage the scroll saw blade every time?
Re: Treehouse 2012
Simplier than that. I just took the drill press and kept making holes next to each other over and over again. Then I threw a rotozip bit into the drill press and slid the wood across to cut out the spaces between the holes. We did use a coping saw a little bit to cut the sharper edges.ciodude wrote:All very creative! I see your kids think like mine do! I am impressed with all the little cut outs for the dinosaur skeletons. Did you have any special tips for that, or just drill and disengage and engage the scroll saw blade every time?
Re: Treehouse 2012
Thanks for sharing. I am not sure I would have thought of that.mebetree wrote:Simplier than that. I just took the drill press and kept making holes next to each other over and over again. Then I threw a rotozip bit into the drill press and slid the wood across to cut out the spaces between the holes. We did use a coping saw a little bit to cut the sharper edges.
Re: Treehouse 2012
I love the stand. We're working on an achievement for our Bear badge where you have to make a display stand for a model you have built, and your design looks much more functional (and easier to build) than what I had come up with! Thanks for sharing the pictures.
Re: Treehouse 2012
These are the instructions I came up with to give to the other den leaders who liked it too.
Parts needed per stand (last number is how long a piece of wood). I personally use pine because it is cheap and drills and nails easily since it is a softer wood.
1” x 4” x 14”
2” x 3” x 4”
¼” x ¼” x 10 ¼”
4 Wood Screws (#6 – 1 ½”)
4 Nails (3/4” long, very skinny, not sure what official size is)
1/8” drill bit
Wood Glue
Directions
1) Cut the 1”x4” piece of wood in half so that you have two 1”x4”x7” pieces of wood. If you would rather pre-cut the wood than have the scout do it, that’s fine.
2) Compound miter cut one end of the 2”x3” at a 10 degree angle in each direction so that it slopes down from one corner to the opposite corner.
3) Cut the ¼” x ¼” piece at the 7” mark at a 45 degree angle back towards the long side. This will leave you with the two pieces needed to prevent the car from sliding off. This is an easy cut for the scouts to make if you want to have them do it.
4) Sand all the pieces of wood to smooth the edges.
5) Pre-drill two holes in the center of both 1”x4”x7” about 3” from each end (which will leave the two holes about an inch apart). I also taper the hole but if you don’t want to you don’t have to.
6) Set one piece of 1”x4” on the side of the 2”x3” that is miter cut to confirm which side of the 1”x4” is lower. Mark the corner of the 1”x4” that is lowest.
7) Put a few dabs of wood glue on the ¼” x ¼” x 7” piece of wood and nail it to the long side of the 1”x4” from step 6 with the mitered end being in the corner you marked in step 6.
Put a few dabs of wood glue on the ¼” x ¼” x 3 ½” piece of wood and nail it to the short side of the 1”x4” from step 6 with the mitered end being in the corner you marked in step 6.
9) Put a few dabs of wood glue on the straight cut end of the 2”x3” and screw the second 1”x4” (the one without the square dowels) into it.
10) Put a few dabs of wood glue on the mitered end of the 2”x3” and screw the first 1”x4” (the one with the square dowels) into it. Make sure that the square dowels are meeting in the low corner.
11) Paint, stain or otherwise decorate.
Parts needed per stand (last number is how long a piece of wood). I personally use pine because it is cheap and drills and nails easily since it is a softer wood.
1” x 4” x 14”
2” x 3” x 4”
¼” x ¼” x 10 ¼”
4 Wood Screws (#6 – 1 ½”)
4 Nails (3/4” long, very skinny, not sure what official size is)
1/8” drill bit
Wood Glue
Directions
1) Cut the 1”x4” piece of wood in half so that you have two 1”x4”x7” pieces of wood. If you would rather pre-cut the wood than have the scout do it, that’s fine.
2) Compound miter cut one end of the 2”x3” at a 10 degree angle in each direction so that it slopes down from one corner to the opposite corner.
3) Cut the ¼” x ¼” piece at the 7” mark at a 45 degree angle back towards the long side. This will leave you with the two pieces needed to prevent the car from sliding off. This is an easy cut for the scouts to make if you want to have them do it.
4) Sand all the pieces of wood to smooth the edges.
5) Pre-drill two holes in the center of both 1”x4”x7” about 3” from each end (which will leave the two holes about an inch apart). I also taper the hole but if you don’t want to you don’t have to.
6) Set one piece of 1”x4” on the side of the 2”x3” that is miter cut to confirm which side of the 1”x4” is lower. Mark the corner of the 1”x4” that is lowest.
7) Put a few dabs of wood glue on the ¼” x ¼” x 7” piece of wood and nail it to the long side of the 1”x4” from step 6 with the mitered end being in the corner you marked in step 6.
Put a few dabs of wood glue on the ¼” x ¼” x 3 ½” piece of wood and nail it to the short side of the 1”x4” from step 6 with the mitered end being in the corner you marked in step 6.
9) Put a few dabs of wood glue on the straight cut end of the 2”x3” and screw the second 1”x4” (the one without the square dowels) into it.
10) Put a few dabs of wood glue on the mitered end of the 2”x3” and screw the first 1”x4” (the one with the square dowels) into it. Make sure that the square dowels are meeting in the low corner.
11) Paint, stain or otherwise decorate.