Arrow of Light Neckerchief Slides
- Scrollsawer
- Master Pine Head
- Posts: 381
- Joined: Sun Dec 30, 2012 4:24 pm
- Location: DFW Metroplex, TX
Arrow of Light Neckerchief Slides
As the Webelos II Den Leader for my twins' Den, I am getting my boys ready to bridge over to Boy Scouts at the end of the month. I had some time to kill before the 'big game' today, so I thought I'd tinker around with some left over basswood to see if I could mock up some concept 'Arrow of Light' neckerchief slides for my boys. I definitely need a better type of wood, and a need a higher TPi blade for the intricate cuts needed in a small space. But overall, I'd say this could work. Would spray paint the arrow bright yellow, the border bright blue, and I'd glue it to a laminate backing (painted dark blue).
I'm not much of a fretwork guy, and these neckerchief slides just need to look good from 2-3 feet away, so they don't need to be perfect. I'm cautiously optimistic I can make these as a nice touch for our Blue & Gold for my boys.
Scrollsawer
I'm not much of a fretwork guy, and these neckerchief slides just need to look good from 2-3 feet away, so they don't need to be perfect. I'm cautiously optimistic I can make these as a nice touch for our Blue & Gold for my boys.
Scrollsawer
"Laugh a while you can Monkey Boy."
Re: Arrow of Light Neckerchief Slides
Nice! How long does it take to cut one of those out? Looks pretty detailed.
birddog
birddog
- Scrollsawer
- Master Pine Head
- Posts: 381
- Joined: Sun Dec 30, 2012 4:24 pm
- Location: DFW Metroplex, TX
Re: Arrow of Light Neckerchief Slides
It takes about 30 minutes per piece. Most of the time is spent trying not to cut what shouldn't be cut, and taking lots of deep breaths between cuts so I don't make a mistake. There's some wood glue fixes evident in the above pic., but since the pieces are being painted, it's not a problem.
"Laugh a while you can Monkey Boy."
- whodathunkit
- Pine Head Legend
- Posts: 2476
- Joined: Sat Apr 25, 2009 5:56 pm
- Location: Forgan, OK
Re: Arrow of Light Neckerchief Slides
Scrollsawer, I know I'm way late on seeing this topic.
And your handy fretwork on the Arrow of Light Neckerchief Slides.
From the photos seen on the fretwork..
And all the starter holes drilled.. to me it looks like your cutting these out one at a time.
In 30 min and you said it is basswood and you need better wood.. & a higher TPI blade.
Very nice work for cutting them out one at a time if you are.
Did not say if you were stack cutting them or not! (How thick are they?)
Higher # blades are for thicker stock & the lower # blades are for thin stock and tight corners.
The fewer the TPI the faster the cut & usually the rougher the cut.
Skip tooth blades cut fastest, Reg tooth blades cut slowest , Double tooth blades are in the middle.
Reverse tooth blades give a splinter free bottom cut but cause the wood to jump & hop around more
so you have to use more hold down pressure.
Anyhow very nice fretwork on the neckerchief slides.
And your handy fretwork on the Arrow of Light Neckerchief Slides.
From the photos seen on the fretwork..
And all the starter holes drilled.. to me it looks like your cutting these out one at a time.
In 30 min and you said it is basswood and you need better wood.. & a higher TPI blade.
Very nice work for cutting them out one at a time if you are.
Did not say if you were stack cutting them or not! (How thick are they?)
Higher # blades are for thicker stock & the lower # blades are for thin stock and tight corners.
The fewer the TPI the faster the cut & usually the rougher the cut.
Skip tooth blades cut fastest, Reg tooth blades cut slowest , Double tooth blades are in the middle.
Reverse tooth blades give a splinter free bottom cut but cause the wood to jump & hop around more
so you have to use more hold down pressure.
Anyhow very nice fretwork on the neckerchief slides.
What type of automobile can be spelled the same forwards & backwards?
- Scrollsawer
- Master Pine Head
- Posts: 381
- Joined: Sun Dec 30, 2012 4:24 pm
- Location: DFW Metroplex, TX
Re: Arrow of Light Neckerchief Slides
Whoda, sorry for the delayed reply. I have only now logged in, for the first time in about a year. I don't recall what type of blade I used, but they were done one at a time (no stack cutting). I do recall that I tried spiral blades, but couldn't maintain enough control to make those work for me. I did have to drill a lot of tiny pilot holes to get the blade in, and that did take a lot of time.
Thanks,
Scrollsawer
Thanks,
Scrollsawer
"Laugh a while you can Monkey Boy."
- whodathunkit
- Pine Head Legend
- Posts: 2476
- Joined: Sat Apr 25, 2009 5:56 pm
- Location: Forgan, OK
Re: Arrow of Light Neckerchief Slides
The spiral blades are even hard for me
to control the cuts with.
I know what you are saying!
Welcome back Scrollsawer!
Sent from my iPhone using Tapatalk
to control the cuts with.
I know what you are saying!
Welcome back Scrollsawer!
Sent from my iPhone using Tapatalk
What type of automobile can be spelled the same forwards & backwards?