Inexpensive bulk weight for workshops

How to have useful construction workshops.
Post Reply
User avatar
FatSebastian
Pine Head Legend
Pine Head Legend
Posts: 2836
Joined: Wed Jun 17, 2009 2:49 pm
Location: Boogerton, PA

Inexpensive bulk weight for workshops

Post by FatSebastian »

Occasionally the subject comes up as to how to supply inexpensive weight in bulk for construction workshops, or family use, when building multiple cars. Ideas on DT have ranged from coins, to steel hardware, to fishing weights, to homemade miniature lead ingots, to removing and recycling tungsten from previously built cars, and so on...

We have come to believe from experience that circular or disc ("coin") fishing sinkers made from lead (Pb) offer an excellent compromise in terms of availability, convenience, efficiency, performance, value, and ease of installation in a build-workshop or clinic environment. This is because circular lead (Pb) sinkers are relatively inexpensive, can be installed with a drill (press) & Forstner bit, can work with a variety of designs (including "wings" / "planks" that aren't too thin), and can be lightened or reshaped if absolutely necessary. There are at least two types of round / discus sinkers: "river" sinkers that are recessed in the center (like a doughnut or inner tube with the hole filled), and "flat" sinkers with, uh, flat sides (coin-shaped). Of the two, the round "flat" sinkers (see image) are the most efficient for derby purposes because they take up less space for the same amount of weight.

Molds under the brand name Do-it allow for the manufacture of standardized round sinkers using molten lead, and there are vendors that make and sell inexpensive sinkers from these molds. Even better, some vendors will pour sinkers without the brass eyelet installed upon request, making them the malleable (but bulkier) equivalent of the original, non-slotted tungsten (W) "rounds". Buying customized sinkers online in quantity is certainly less hazardous, and likely cheaper, for ordinary derby construction purposes than DIY molten-lead pouring. In the interest of promoting safety and economy, I have a vendor recommendation over in the "Derby Products and Services" forum; although there are other sources, this vendor told me that omitting the eyelet was actually a common customization request.

With all that said, the main purpose of this thread is to document the dimensions of the Do-it mold's round flat sinkers so that people can know how to design their cars around them, and have the proper tools on hand to install them. Keep in mind that the listed weight of these sinkers is not exact; it is close but the actual weight can vary from piece to piece or batch to batch by, say, hundredths of an ounce. The one sinker listed here that was consistently different from its advertised value was the very wide 3 oz flat, which ranges 2.8 - 2.9 ounces (and may not be from a Do-it brand mold specifically). While the 3 ounce weight is the thinnest of all the discs, its diameter also equals the width of the standard pinewood block, so few designs will easily accommodate it.

Code: Select all

List Wt (oz)	Diameter (")	Thickness (")	Diameter (mm)	Comment
1/4		9/16		7/32		14.3
3/8		21/32		7/32		16.6
1/2		3/4		7/32		19.2		Press fit in 3/4" hole	
3/4		7/8		7/32		22.4		Press fit in 7/8" hole
1		63/64		7/32		25.0		Loose fit in 1" hole
1-1/4	 	1-1/128		9/32		25.6		Press fit in 1" hole
1-1/2		1-1/32		5/16		26.2
1-3/4		1-1/16		11/32		27.2
2		1-1/8		11/32		28.3		Snug fit 1-1/8" hole
3		1-3/4		3/16		44.3		Relaxed fit in 1-3/4" hole, ~2.85 oz actual
To evaluate the usability of lead discs, test holes were cleanly drilled into pinewood using Forstner bits and a drill press, and then filled with raw (unpainted) rounds. In the table comments above, a "press" fit implies a tight friction fit that will not fall out, because the disc needs to be forcibly pressed or tapped into the hole. A "snug" fit suggests a friction fit that can be knocked loosed if slapped hard enough against an object; a "relaxed" fit is a friction fit that stays in place yet might fall out during normal handling or racing conditions, so it is best to glue in place or paint the weight before installation to give it a bit more dimension. A "loose" fit means that adhesive is definitely needed to ensure that the weight doesn't fall out of the bottom of the car (viscous wood glue seems sufficient). The dimensions are close approximations, as there will be natural variations between individual pieces...

In our workshops, we find that the 2 ounce size is probably most popular; it is the cheapest per pound and thus the best value, and can be drilled out if 2 ounces is too much. We can recommend the 1/2-, 3/4-, 1-, 1-1/4-, 2-, and 3-ounce sizes for those owning a Forstner bit set in 1/8" increments. The others are going to require specially sized (maybe metric) Forstner bits, which if purchased individually, drives up the overall cost of using this kind of weight.

Spray painting these rounds could make them safer to handle, and they could be painted different colors to "color code" them according to weight and hole size. But painting might also affect their fit (some fit pretty tightly already!), depending on the type of paint.

If somebody wants to experiment with these without making a bulk purchase online, some sporting goods stores sell round sinker weights depending on where you live (and these can be significantly discounted outside of fishing season). Of course, these may not be the same "flat" type as described above, and they will have the eyelet installed.

To remove a brass eyelet, insert a long nail into the eyelet and twist. Usually the eyelet snaps off cleanly flush, but if it breaks, use pliers to pull off or cut away any jutting brass wire. If the eyelet removal process malforms the sinker, you can tap the malleable lead back into its original shape using a small hammer.

Image
Post Reply